Super-Trete 110-VOC Specification Sheet

CRESSET CHEMICAL COMPANY

Form Release Agents    Cures  Seals  Etc.    Form Treatments    Testimonials    Contacts

Specs  MSDS  Properties     Form Sprayers    Order FREE Literature    Cleaners

Instructional Literature   Regulations   Trade Shows   Related Industry Links   Aerosols

SPECIFICATION SHEET SUPER-TRETE 110-VOC CURE & SEAL

Super-Trete 110-VOC is a low solids, water based cure and seal. It meets ASTM specifications and all state and federal VOC regulations.Updated May 2007.

Environmental Report Card Non-toxic.................Yes Non-flammable.............Yes VOC compliant.............Yes Solventless...............Yes Water based...............Yes

1. PRODUCT
Super-Trete 110-VOC Cure & Seal

2. MANUFACTURER
Cresset Chemical Company, Inc. One Cresset Center, Box 367
Weston, OH 43569 800-367-2020 USA & Canada
419-669-2041
(Fax) 419.669.2200
www.cresset.com
cresset@cresset.com

3. PRODUCT DESCRIPTION
Basic Use: Super-Trete 110-VOC Cure & Seal is an ASTM Type 1 class B or Type I-D class B curing compound for use on fresh concrete. It is also a sealer for use on cured concrete...floors, panels, walls, columns, precast or prestressed. Use it to protect architectural concrete such as exposed aggregate, hard landscape products, ornamental objects, etc. As a curing compound it:

Is water based
Covers up to 200 square feet per gallon
Has no unpleasant odors
Physically combines with surface matrix of the concrete
Exceeds California SCAQMD rule 1113-90
Is non-flammable
Applies easily by sprayer, roller or brush
Is fast drying
Shows temporary "white when wet" color where freshly applied
Wets fresh concrete better than solvent based cure and seals
Dries clear

As a sealer it helps:

Prevent concrete dusting
Prevent liquids from soaking into the concrete
Provide for easier cleaning
Prevent carbon dioxide concrete reaction
Reduce clean-up costs from construction soils
Minimize salt water penetration

Limitations: Do not apply over puddles on the surface of the concrete. Do not use if temperature drops below 50° F. Protect from freezing.

Ground Shipping in the USA: Containers holding 275 gallons or 55 gallons or 5 gallons or less (regardless of quantity) are not federally regulated and shipping product in the Cresset package does not require following hazardous shipping requirements.

Applicable Standards: Exceeds ASTM C-309-89 for water retention at the rate of 200 square feet per gallon. Exceeds California SCAQMD VOC rule 1113-90. ASTM C-309 officially replaces canceled Federal Specification TT-C-800A.

VOC means "Volatile Organic Compounds". For curing and sealing materials California requires a VOC of 350 grams per liter or less. (The smaller the number, the safer you are.) Super-Trete 110-VOC Cure & Seal has 130 grams per liter of VOCs, which greatly exceeds these stringent regulations.

4. TECHNICAL DATA
Please see Table.

TABLE OF PROPERTIES

		`Metric`
`Color`	White	`White`
`Freeze Thaw Stability`	Do not freeze	`Do not freeze`
`Shelf Life`	`8 Months`	`8 Months`
`Resin`	`Acrylic`	`Acrylic`
`Flash Point`	`Not Applicable`	`Not Applicable`
`Viscosity (centipoises)`	`2 @ 68° F`	`2 @ 20° C`
`Tack Free`	`50 Minutes`	`50 Minutes`
`Dry Hard`	`10 Hours`	`10 Hours`
`Density`	`8.44 lbs/gal`	`1011 g/L`
`VOC (Volatile Organic Compounds)`	`130 g/L`	`130 g/L`
`VOC (Volatile Organic Compounds)`	`1.08 lbs/gal`	---

Composition: A proprietary emulsion of acrylic polymers in water. Contains no waxes, no chlorinated hydrocarbons...no carcinogens.

5. APPLICATION
As a curing compound (on fresh concrete): Apply to fresh concrete after all the free water has disappeared and concrete has taken an initial set. (OBTAIN YOUR BEST CURE BY APPLYING SUPER-TRETE 110-VOC WHILE THE CONCRETE IS STILL MOIST...BUT PUDDLES ARE NOT PRESENT.) Spray, roll or brush Super-Trete 110-VOC Cure & Seal onto the concrete surface uniformly at a rate of 200 square feet per gallon.

As a sealer (on hardened concrete): Prepare hardened concrete by removing any dirt, oil and other soils from the surface. MOISTEN DRY CONCRETE WITH WATER (no standing puddles, however). Apply at a rate of 200 to 400 square feet per gallon.

Notes to Specifier: 1. Moisten concrete with water before applying. Dry concrete absorbs water from the "wet" Cure & Seal hindering proper film formation. Using Super-Trete on dry concrete may result in a film with a white, flaky or dusty appearance as well as poor adhesion to the concrete’s surface.

2. Hot, windy conditions may cause "checking" of the acrylic film. Windy, drying conditions may prematurely harden the very top surface, trapping other ingredients underneath. Proper hardening allows for slow removal of all materials throughout the film’s thickness.

3. Avoid extra thick applications. Apply several thin coats rather than one thick coat. On thick coats the surface may harden first, trapping other materials in the film. This results in a white appearance. Frequently, the white disappears in a few weeks.

6. AVAILABILITY AND COST
Availability: Super-Trete 110-VOC is available in 1 and 5 gallon containers; recyclable orange and white plastic 55 gallon drums and 275 gallon MegaPaks. Contact Cresset Chemical Company for your nearest distributor.

Cost: The cost on hard, smooth surfaces is about $0.03 per square foot (January 2007).

7. LIMITED WARRANTY
Cresset Chemical Company warrants the product against defects in materials for a period of 8 months from purchase. If Cresset receives notice of such defects during the warranty period, Cresset at its option will either replace the product or refund the purchase price. THE WARRANTY SET FORTH ABOVE IS EXCLUSIVE AND NO OTHER WARRANTY, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED. CRESSET SPECIFICALLY DISCLAIMS THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE REMEDIES PROVIDED HEREIN ARE BUYER'S SOLE AND EXCLUSIVE REMEDIES. IN NO EVENT SHALL CRESSET CHEMICAL COMPANY BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF PROFIT) WHETHER BASED ON CONTRACT, TORT OR ANY OTHER LEGAL THEORY.

8. LIMITED WARRANTY
Not required.

9. TECHNICAL SERVICES
Cresset Chemical Company specializes in developing, distributing and servicing release agents. Our technical support includes assistance in optimizing concrete mixtures for achieving architectural surfaces; release agent compatibility with superplasticizers, coatings, form facings, etc.; and solving other concrete surface blemish problems.

Free literature includes:

Catalog of products
Material Safety Data Sheets
"Cresset Concrete Standards" (Application techniques to obtain high visual impact concrete surfaces)
"Surface Voids and How to Eliminate Them"

Over 75 distributors in the United States, Canada, Australia and Germany to serve you. Your technical inquiries are welcome, please call, write or FAX.

For the most up-to-date copy please download from Cresset Chemical Company's web site, www.cresset.com, or contact us for a printed copy.

Other Specification Sheets:
Index of All Cresset's Specification Sheets
Crete-Trete 309-VOC Cure & Seal
Crete-Trete 400 Anti-Check Cure
Super-Trete 115 Matte Sealer
Crete-Trete 350 Water Repellent

Form Release Agents    Cures  Seals  Etc.    Form Treatments    Testimonials    Contacts

Specs  MSDS  Properties     Form Sprayers    Order FREE Literature    Cleaners

Instructional Literature   Regulations   Trade Shows   Related Industry Links   Aerosols

Return to Cures/Seals/Etc. Page

Cresset Home Page

Cresset and Super-Trete are trade marks of Cresset Chemical Company.